+- XOR Userforum (https://forum.xor.eu)
+-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3)
+--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6)
+---- Forum: Firmware / Manual (https://forum.xor.eu/forumdisplay.php?fid=11)
+---- Thread: Release Candidate Firmware V1.21 RC4 (/showthread.php?tid=625)
RE: Release Candidate Firmware V1.21 RC1 - ello - 02-18-2020
is it only me? i thought when you add a new note it gets it's value from the previous entered note. now i get for example a "c-7" when previously i created a "c-4". this happens in track 7 and 8. in the tracks 1...6 it works.
maybe it never worked in track 7 and 8, but i just came along that. dunno if it is a bug
RE: Release Candidate Firmware V1.21 RC1 - XORadmin - 02-18-2020
(02-18-2020, 05:30 PM)ello Wrote: is it only me? i thought when you add a new note it gets it's value from the previous entered note. now i get for example a "c-7" when previously i created a "c-4". this happens in track 7 and 8. in the tracks 1...6 it works.
maybe it never worked in track 7 and 8, but i just came along that. dunno if it is a bug
I will check that. It might be possible that when created a new note then the last note is not being saved.
RE: Release Candidate Firmware V1.21 RC2 - XORadmin - 02-18-2020
I just uploaded RC2:
- added squaresample to the waveforms (for the toddlers
)- added Pulswidth Change for squarewave through offset FX command (also from automators usable for some nice PWM sweep)
- fixed sample output leak to next sample output
- added Trigger as Sample FX effect. Triggers 1..6 can also be controlled from the sample tracks. Makes probably sense when using a waveform and want to trigger an envelope at the same time.
- added waveform prelisten
- fixed last note value for sample when editing
- renamed LFO Range to Amplitude
- and some CV16 stuff under the hood (nearly there, just some minor usability stuff to do from the beta reports)
RE: Release Candidate Firmware V1.21 RC2 - misk - 02-18-2020
awesome! i just happened to be on here reading about trigger timing — i'll check it out asap
RE: Release Candidate Firmware V1.21 RC2 - zerius - 02-19-2020
Any infos concerning envelopes mod outputs ? Would love see them come in in the next firmware
RE: Release Candidate Firmware V1.21 RC2 - funqpatrol - 02-19-2020
cool, out of curiosity what's the motivation behind turning the Nerdseq into an oscillator?
RE: Release Candidate Firmware V1.21 RC2 - XORadmin - 02-19-2020
(02-19-2020, 12:29 AM)zerius Wrote: Any infos concerning envelopes mod outputs ? Would love see them come in in the next firmware
This is not on top of my 2do list and don‘t be too excited about that either. I am sure they will be mostly average compared to analogue ones. The update time of the automators won‘t allow too snappy envelopes, so their general use will be mostly for something in the slower than 100ms attacks/releases.
RE: Release Candidate Firmware V1.21 RC2 - Barney Rubble - 02-19-2020
Found a bug in tables - but is probably not RC2 related - but I'm reporting it here just in case it is.
Open table put value into FX digits column without assigning an FX. Value goes to 4 digits "FFFF" and it will not reset using the delete key.
Sorry just realised if I press delete then first three digits reset to zero and then if I go back to pattern screen and go back into the table the fourth digit is gone!
RE: Release Candidate Firmware V1.21 RC2 - XORadmin - 02-19-2020
(02-19-2020, 03:45 PM)Barney Rubble Wrote: Found a bug in tables - but is probably not RC2 related - but I'm reporting it here just in case it is.
Open table put value into FX digits column without assigning an FX. Value goes to 4 digits "FFFF" and it will not reset using the delete key.
Sorry just realised if I press delete then first three digits reset to zero and then if I go back to pattern screen and go back into the table the fourth digit is gone!
Yes next time. Tables are on the list for later. Didn‘t change anything there so it‘s ‚old‘. But noted! Thx
RE: Release Candidate Firmware V1.21 RC2 - ello - 02-19-2020
cool. and i really like having those basic waveforms thus i can use my vco modules for more important stuff and still have some basic possibilities. great update so far