+- XOR Userforum (https://forum.xor.eu)
+-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3)
+--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6)
+---- Forum: Firmware / Manual (https://forum.xor.eu/forumdisplay.php?fid=11)
+---- Thread: Firmware V1.21A (/showthread.php?tid=652)
RE: Firmware V1.21 - XORadmin - 03-14-2020
(03-14-2020, 06:13 PM)premini Wrote: Hi, with regards to:
"- added delayed reset function so the reset comes a bit later after the last clock when stopping the sequencer."
Is this delay configurable? I am still experiencing a clk arriving right after the reset.
Thanks.
I think that it is not correct. The reset always came right after the last clock, also in older versions. The time increased now to 5 milliseconds. So the reset pulse comes 5 milliseconds after the last clock was released. This time is fixed and gear should be able to handle it properly.
On top of that i added another reset pulse generation when pressing SHIFT+STOP if the sequencer is stopped. That should be fine to get everything to run well.
RE: Firmware V1.21 - premini - 03-15-2020
(03-14-2020, 06:31 PM)XORadmin Wrote:(03-14-2020, 06:13 PM)premini Wrote: Hi, with regards to:
"- added delayed reset function so the reset comes a bit later after the last clock when stopping the sequencer."
Is this delay configurable? I am still experiencing a clk arriving right after the reset.
Thanks.
I think that it is not correct. The reset always came right after the last clock, also in older versions. The time increased now to 5 milliseconds. So the reset pulse comes 5 milliseconds after the last clock was released. This time is fixed and gear should be able to handle it properly.
On top of that i added another reset pulse generation when pressing SHIFT+STOP if the sequencer is stopped. That should be fine to get everything to run well.
Yes. I tried the Shift Stop when stopped and its working fine.
If i don't do that, Circadian advances one step right after I stop Nerdseq (as usual).
RE: Firmware V1.21 - XORadmin - 03-15-2020
(03-15-2020, 12:28 AM)premini Wrote:(03-14-2020, 06:31 PM)XORadmin Wrote:(03-14-2020, 06:13 PM)premini Wrote: Hi, with regards to:
"- added delayed reset function so the reset comes a bit later after the last clock when stopping the sequencer."
Is this delay configurable? I am still experiencing a clk arriving right after the reset.
Thanks.
I think that it is not correct. The reset always came right after the last clock, also in older versions. The time increased now to 5 milliseconds. So the reset pulse comes 5 milliseconds after the last clock was released. This time is fixed and gear should be able to handle it properly.
On top of that i added another reset pulse generation when pressing SHIFT+STOP if the sequencer is stopped. That should be fine to get everything to run well.
Yes. I tried the Shift Stop when stopped and its working fine.
If i don't do that, Circadian advances one step right after I stop Nerdseq (as usual).
I think the problem can be only in the CR then. The reset comes definitely long after the last clock.
RE: Firmware V1.21 - basswave - 04-01-2020
excellent thank you very much
RE: Firmware V1.21A - XORadmin - 04-01-2020
I just uploaded a maintenance version (V1.21A) with some minor fixes of reported bugs:
- Fixed BPM change which was introduced with the last version
- Fixed ignored BRK in Midi FX when Midi track is muted
- Fixed loading Hz/Volt in Project
- Some minor GUI updates