+- XOR Userforum (https://forum.xor.eu)
+-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3)
+--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6)
+---- Forum: Firmware / Manual (https://forum.xor.eu/forumdisplay.php?fid=11)
+---- Thread: New Firmware 1.16 Preview (/showthread.php?tid=176)
RE: New Firmware 1.16 Preview - XORadmin - 06-07-2018
(06-07-2018, 10:06 PM)Onosendai Wrote: I try to send a LFO to the MOD 1 out, but it do nothing ?
- Slot 0 = LFO
- Play sign ok
- On the "1" i choose 01
Then nothing. It works if i choose 00 (CV)
It will be fine in the release version!
RE: New Firmware 1.16 Preview - Human_Machine_Connection - 06-16-2018
hello
thanks for this update
is there any way to trig lfo reset?
RE: New Firmware 1.16 Preview - XORadmin - 06-16-2018
(06-16-2018, 03:47 PM)Human_Machine_Connection Wrote: hello
thanks for this update
is there any way to trig lfo reset?
Yes, you can press OK when you are on the reset position in the LFO (most left below) to manually reset (eg set it to the phase position) or from the sequencer at any point of course.
RE: New Firmware 1.16 Preview - holo - 06-17-2018
(06-16-2018, 04:25 PM)XORadmin Wrote:(06-16-2018, 03:47 PM)Human_Machine_Connection Wrote: hello
thanks for this update
is there any way to trig lfo reset?
Yes, you can press OK when you are on the reset position in the LFO (most left below) to manually reset (eg set it to the phase position) or from the sequencer at any point of course.
hi, how do i retrigger it from sequencer?
RE: New Firmware 1.16 Preview - XORadmin - 06-17-2018
You can manipulate all automator slots and their values from the FX column
RE: New Firmware 1.16 Preview - holo - 06-17-2018
saw the command but couldnt really find out how its used. could you give me a hint? is it described somewhere?
RE: New Firmware 1.16 Preview - XORadmin - 06-17-2018
(06-17-2018, 05:54 PM)holo Wrote: saw the command but couldnt really find out how its used. could you give me a hint? is it described somewhere?
It's not described yet.
If you take Automation Slot 0: The first digit is the function and the last digits is the value.
If you have the LFO on slot 0 then it is the following:
ASL0 0xx Start/Stop Slot 0 (00 stop, 01+ start)
ASL0 1xx Reset LFO (resets doesn't care about number)
ASL0 2xx LFO Speed (00 lowest, FF fastest)
ASL0 3xx LFO Offset (00 negative offset, 80 zero offset, FF positive offset)
and so on. You can see the functions in the status bar.
RE: New Firmware 1.16 Preview - holo - 06-17-2018
thank you, thats helping
in the track status bar this doesnt show up btw, would be nice though.. instead of 'automation slot x'
RE: New Firmware 1.16 Preview - XORadmin - 06-17-2018
(06-17-2018, 07:13 PM)holo Wrote: thank you, thats helping
in the track status bar this doesnt show up btw, would be nice though.. instead of 'automation slot x'
Hmm? It does show up when you are on the values field. Just checked.
RE: New Firmware 1.16 Preview - holo - 06-17-2018
(06-17-2018, 07:27 PM)XORadmin Wrote:(06-17-2018, 07:13 PM)holo Wrote: thank you, thats helping
in the track status bar this doesnt show up btw, would be nice though.. instead of 'automation slot x'
Hmm? It does show up when you are on the values field. Just checked.
hmm.. funny .. i can see them now too but i also checked right before, twice, even ran through the numbers, and i can hardly believe that i missed it because i did look fot them at just the same spot where i can see them now..
a brain glitch maybe
