![]() |
|
Mapping Discussion - Printable Version +- XOR Userforum (https://forum.xor.eu) +-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3) +--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6) +---- Forum: General Questions (https://forum.xor.eu/forumdisplay.php?fid=17) +---- Thread: Mapping Discussion (/showthread.php?tid=1712) |
RE: Mapping Discussion - XORadmin - 02-10-2024 (02-09-2024, 09:59 PM)shledge Wrote: Still can't get it to work - I did the following Confirm that it doesn't work correctly. I fixed it already and the release is following shortly. RE: Mapping Discussion - shledge - 02-12-2024 (02-10-2024, 04:40 PM)XORadmin Wrote:(02-09-2024, 09:59 PM)shledge Wrote: Still can't get it to work - I did the following Using the above steps? If it is working, do I need the variables to set initial pitch and volume? RE: Mapping Discussion - vjrt - 04-09-2024 Hi, I’m struggling trying to use the Nerdseq as an arpeggiator for external gate inputs. What I do is set in Mapping screen: CV IN 1→ TRIG TRIG TR 1 And then make a pattern of just one step in Track 1 with a Table00 set on CV In 1 as source on it and a gate off and a note off in the respective columns. It works fine but when I reboot my system the table doesn’t start until I put a note in the note column, and then put a note off again. What is the correct method to have a track doing arpeggios of an external gate input? Thanks in advance! RE: Mapping Discussion - XORadmin - 04-09-2024 (04-09-2024, 03:18 PM)vjrt Wrote: Hi, I can’t really follow what you do and want to achieve. How is the mapping related to this? You use the CV as table source to progress the table steps? If you use table transpose you need at least one basenote where it transposes from and that is derived from the played pattern note. RE: Mapping Discussion - vjrt - 04-09-2024 (04-09-2024, 07:06 PM)XORadmin Wrote:(04-09-2024, 03:18 PM)vjrt Wrote: Hi, RE: Mapping Discussion - XORadmin - 04-12-2024 (04-09-2024, 08:36 PM)vjrt Wrote: Thanks for the quick reply. I'm not sure is necessary to do that mapping, if there is a simpler way is better. Just to be sure: - Tables are only running when the sequencer is running. - Tables need to be started at some point and don't start by itself (and so don't iterate through the table steps) - There is no basenote defined after startup and so the table never knows from which note it should transpose so it skips the transposition. Thats why at least once a note should have played to be able to transpose it. I can't think of a way to get around this at the moment as the tables are build around a pattern currently and there is no way to feed it with an external basenote. RE: Mapping Discussion - FiFitheGreater - 06-09-2024 Hello, I was wondering if it was possible to assign an i2c source, a fader from F8r in this case, to the note value of a specific step on a track. I imagine assigning each fader to a different note in an appropriate length pattern to create a pseudo-step sequencer, allowing the manipulation of the value of each step on the fly. Thank you! RE: Mapping Discussion - XORadmin - 06-09-2024 (06-09-2024, 08:46 PM)FiFitheGreater Wrote: Hello, Yes RE: Mapping Discussion - kriskeyman - 06-18-2024 Is it possible to change the range of an F8R slider mapped to transpose of a track? I’d like to modify the range of the slider so that slider at 00 (slider at bottom) maps to - - (no) track transpose. Then if I raise the slider to max, I’m only getting +1 octave. Can Nerdseq handle this adjustment, or do need to modify F8R firmware to adjust? RE: Mapping Discussion - XORadmin - 06-18-2024 (06-18-2024, 06:46 AM)kriskeyman Wrote: Is it possible to change the range of an F8R slider mapped to transpose of a track? I’d like to modify the range of the slider so that slider at 00 (slider at bottom) maps to - - (no) track transpose. Then if I raise the slider to max, I’m only getting +1 octave. Can Nerdseq handle this adjustment, or do need to modify F8R firmware to adjust? Easy. I2C SCCV …. CALC RNGE VAVB And in VA and VB you decide the lowest point and the highest point. Also forget about F8R in that situation. A source can be anything, a F8R, a CV input, an Midi CC or the current bpm or whatever. All kind of values can be a source so it doesn’t matter if it is a fader or what else. |