![]() |
|
More Triggers 16 Triggers Staying High - Printable Version +- XOR Userforum (https://forum.xor.eu) +-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3) +--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6) +---- Forum: General Questions (https://forum.xor.eu/forumdisplay.php?fid=17) +---- Thread: More Triggers 16 Triggers Staying High (/showthread.php?tid=2127) |
More Triggers 16 Triggers Staying High - tenshun - 11-14-2026 Just Upgraded firmware to 3.03 and use Midi (Befacco Cv Thing in Note Gate mode) to send and record triggers into a Trigger 16 channel. I noticed that if i send a trigger It stays High and does not turnoff. i have to press the Shift + Stop to reset it back to normal. I have not had this problem before. Before i would be able to rehearse some drum patterns before i can record them into Nerdseq and now it seems This does not work. Any way i might be missing a setting? RE: More Triggers 16 Triggers Staying High - XORadmin - 11-14-2026 (11-14-2026, 06:13 AM)tenshun Wrote: Just Upgraded firmware to 3.03 and use Midi (Befacco Cv Thing in Note Gate mode) to send and record triggers into a Trigger 16 channel. Is it an old project you loaded or a new one from scratch? I just checked it and here the manual doesn't match what the NerdSEQ is actually doing. The note names are incorrectly in the manual and the gates into matrix starts from C-4 (note number 48). These are gate on and off and it sets the matrix column on recording. The notes from 24 (C-2) do only set the gate while they should usually fire a trigger. That is wrong. For now use the note numbers from C-4 and you can record into the matrix and I expect the CV Thing sends also a note off so it will reset again. The other parts, manual and the triggers are for me to fix in the code. So from C-2 is unusable and from C-4 does work. The none working part will be fixed with the first maintenance update. The code actually didn't change lately. It's been like this since at least 2023 (I didn't look further). RE: More Triggers 16 Triggers Staying High - tenshun - 11-14-2026 Hello, i switched to note 48 on the CV Thing in Note Gate function and the triggers still leave the gate High. Whats really strange is that when i go to record my trigger patterns then it will take a few steps to register them as triggers and it will record. But as soon as i stop recording then the triggers get set the trigger to a gate which does not turn off only when i press Shift + Stop. I also noticed that I am using Track 8 for my trigger 16 channel yet when i play back my triggers that are on Track 8 they are showing up on track 1 in the Recent notes. it must be a setting i have turned on or something RE: More Triggers 16 Triggers Staying High - XORadmin - 11-14-2026 (11-14-2026, 03:13 PM)tenshun Wrote: Hello, I just tested it and Note 48+ works fine. In your case I am sure the CV Thing doesn't send a note off after the note on. You would need to enable that on the CV thing. Recording and playing is fine, also on Track 8. No 'ghost' triggers on track 1. Maybe you got your Trigger16 columns set to the triggers 1..6? RE: More Triggers 16 Triggers Staying High - tenshun - 11-15-2026 So i checked the settings on the befacco cv thing and i didn’t change anything from the previous version and the track assign for the Trigger 16 is on track 8. This was with new project loaded. Is there a way i can jump back to the previous firmware? As of right now this is kinda of a jam on my music creation. Where are the previous firmwares located? I think i will just stick to the 3.00 for awhile as it was working flawless for what i was using. RE: More Triggers 16 Triggers Staying High - tenshun - 11-15-2026 Ok so i was able to get it working by changing the settings in the Befacco CV thing from Note Gate to V/Oct to Note. Its a bit weird as i have to make the triggers go through the Jazmine Olive trees Traffic in order for me get the notes for trigger 1 and trigger 2 ,Then the output goes into the Befacco cv thing. Weird work around! RE: More Triggers 16 Triggers Staying High - XORadmin - 11-15-2026 Ok I checked again (for V3.0) and checked only for recording before (Track record) and there it had the same issues. The Track playing actually did send out a trigger. That did change and is wrong now. So for the playback it did work for you before. Will be fixed with the maintenance version. Sorry for the trouble. Btw. You can always 'downgrade' the firmwares. They are still to download on the forum. RE: More Triggers 16 Triggers Staying High - tenshun - 11-15-2026 No worries. I was able to get it working with a different work around. just had to incorporate some other modules to make the Trigger have the note off. Before i figured out the work around i did try and go back to the previous firmware (3.00) but it was not working because i updated the duel chord and the More Trigger 16 firmwares so it was behaving strange. Maybe because the newer firmwares do not work with 3.00. RE: More Triggers 16 Triggers Staying High - XORadmin - 11-16-2026 (11-15-2026, 04:13 PM)tenshun Wrote: No worries. I was able to get it working with a different work around. just had to incorporate some other modules to make the Trigger have the note off. No they work also fine with V3.0. Maybe the strange behaviour is that you loaded projects that have been saved with V3.03? Only thing is that D0 - EF are working in the old way on the trigger16 and you might not want to use them then. |