+- XOR Userforum (https://forum.xor.eu)
+-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3)
+--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6)
+---- Forum: Nerdseq issue / bugreport (https://forum.xor.eu/forumdisplay.php?fid=8)
+----- Forum: Beauty and less important bugs/glitches (https://forum.xor.eu/forumdisplay.php?fid=16)
+----- Thread: *SOLVED* never in sync (/showthread.php?tid=154)
RE: never in sync - tuj - 04-01-2018
ok so the clock tests all passed, all four said 'ok' with cable from out->in on reset and clock.
BTW, in that configuration, when I accidentally scrolled down to "test sample 7", it locked up.
RE: never in sync - Patate le mage - 04-02-2018
Hi Tuj, i tried with :
Metropolis
Eloquencer
It works like a charm
I tried with Trigger riot
It works but it is tricky because of how the trigger riot is working.
RE: never in sync - tuj - 04-02-2018
I have tried clocking with:
ES-4+ES-8GX
Trigger Riot
RCD
SCM
QCD
The ES-4 clocking (both sync and reset) works with:
Rene
Trigger Riot
Stilson Hammer MK2
Varigate4
ER101
RCD
SCM
QCD
A151
Grids
A155
DLD
Echophon
Z-DSP clocked delays
I'm baffled. All my other modules work correctly. The NerdSeq is always 1 step behind and reset signal does nothing.
RE: never in sync - Patate le mage - 04-02-2018
You can try this:
put the nerd seq in slave mod
put a clock in the clock in
and a manual gate in the reset ( ls1 or something )
let's play the nerseq, and look at the pattern screen. Does it reset when you touch your manual gate ?
RE: never in sync - tuj - 04-02-2018
Patate: I will try that, but like I said before, I ran the reset into a decay envelope to increase the duration of the reset pulse. Didn't make any difference, the reset doesn't do anything. I'll try a manual gate when I get back home and see what happens.
RE: never in sync - XORadmin - 04-02-2018
But also without the reset connected it should work well.
Did you try to go down and up again with the cursor on the calibration, checking if the clock/reset doesn't show ERR?
Also, how do you mean that it was locked up? That never happened to me and i calibrated quite some NerdSEQ.
RE: never in sync - tuj - 04-25-2018
OK some people on Reddit are telling me that the reset needs an INVERTED TRIG? Is this true?
I have a lot of modules, and none of them use an inverted trig for anything.
RE: never in sync - XORadmin - 04-25-2018
No thats not true.
The reset input uses a standard trigger.
Please make this easy test. Set to clock MOD Slave
Connect the clock input to a external clock source.
Connect output trigger 1 with the reset input.
Make a pattern on track 1 and set the trigger on position 8 with value 40.
Start the external clock and start the pattern.
The sequencer should run now and only do a 8 step sequence and reset then. If it keeps running to 64 steps then you reset input is bad.
Sorry to not getting back earlier for some additional tests.
RE: never in sync - tuj - 04-25-2018
OK, I will try your test when I get home today. Thank you for the prompt response. I have no idea why some people spout off garbage.
RE: never in sync - tuj - 04-28-2018
OK, here's what I did:
new pattern, track 1
on step 8 I put a 40 trigger
press start
verify that trigger 1 out is producing a 5v spike on step 8.
plug trigger 1 out to reset in
sequence should restart at step 8; instead reset is ignored and continues to play whole pattern.
EDIT: I didn't see your part about external clock...
when i set to external clock, 16 step and route the trigger 1 to reset in, it DOES reset on step 8.
So reset is working apparently.