+- XOR Userforum (https://forum.xor.eu)
+-- Forum: Products (https://forum.xor.eu/forumdisplay.php?fid=3)
+--- Forum: NerdSEQ (https://forum.xor.eu/forumdisplay.php?fid=6)
+---- Forum: General Questions (https://forum.xor.eu/forumdisplay.php?fid=17)
+---- Thread: CV16 some notes not being played (/showthread.php?tid=978)
CV16 some notes not being played - mgd - 01-23-2021
Hi Forum,
I have been playing around with sequencing 3 tracks with 3 notes and gates/mods per track (i.e. 9 notes and mods in total). The track setup is like this:
Track 1: ext CV 1-6 (notes and gates/mods alternating)
Track 2: ext CV 7-12 (notes and gates/mods alternating)
Track 3: ext CV 13-16, ext CV 5-6 (notes and gates/mods alternating)
Obviously ext CV 5 and 6 were allocated twice. For the time being I don't care and meanwhile I changed those two tracks to local CV 6/local mod 6.
The strange behaviour I encountered was with the double allocation of ext CV 5-6.
All 3 tracks have patterns in all sequencer rows from 00 to 0F.
Here is what happened:
I played the whole 3 tracks starting from sequencer row 00 and in row 02 Track 3 missed out on a couple of notes.
Tried again from 00 and again the notes were missing.
Then played Track 3 alone from row 02 and the notes were there.
Then played Track 3 alone from row 00 and the notes were there.
Now played all tracks from row 02 and the notes were there.
Going back one row and played all tracks from row 01 and the notes were there.
Going back one row and played all tracks from row 00 and the notes were missing.
Went into track setup, loaded calibration data, moved the cursor around a bit and played all tracks from row 00 again and all notes were there. From here on I have not been able to make the notes disappear during playback again.
I switched off my modular in case it is an initial setup issue but so far the problem did not reappear. I also have changed the double allocation of ext CV 5-6 as described above.
I have no idea wether the loading of calibration data for the CV16 had anything to do with it but I thought I'd report the whole thing in case someone else stumbles across something similar.
Kind regards,
Michael
RE: CV16 some notes not being played - XORadmin - 01-23-2021
Actually loading the calibration data is not related at all. The calibration is inside the CV16 and it sends only some numbers back to the NerdSEQ.
They are 3 possibilities:
1. Your CV16 Firmware is still V1.0 which might interfere with other expander sequencing.
2. You have some probabilities on several outputs
3. (and this is the most common) You have modulators running which overrule Note behaviour. It might be possible that you started modulators in some ways but are not aware of it (though you can always see if modulators are running on top of the columns). Press SHIFT+STOP twice always turns all modulators off.
RE: CV16 some notes not being played - mgd - 01-23-2021
Hi Thomas,
thank you for your response.
1. I think my CV16 is on V1.1. I updated it and that's what it says upon booting.
2. no probability whatsoever in the whole project (AFAICT from looking into the patterns)
3. modulators seem unlikely as the only ones I'm currently using are ^11 and -16. When checking the stuff by listening to it I always stop by pressing SHIFT+STOP twice to make sure all gates are off and there remain no droning sounds.
It still has not yet reappeared though. My guess is that for some strange reason the system got into a weird state but I have no clue as to how that possibly could have happened. I reported it mostly to create a record in case someone else (or me
) encounters a similar problem in the future.At this point in time I would ignore it
Kind regards,
Michael