This is it! The latest MAJOR Firmware for the NerdSEQ and this time also a massive update for the Video Expander (VEX).
Welcome V3.0!
As usual loads of new features, fixes and if you got a Video Expander then you get also a Video Synthesizer for free! If you don't then now is the time to get your hands on a VEX ;-)
Important information before you update!!!
- make a backup of your SD Card and especially of your projects (can't stop repeating that!!)
- Firmware update FAQ for some infos. https://forum.xor.eu/showthread.php?tid=4
- No worries, in case of any issues you can always go back to your earlier version (but can't load projects that have been saved with V3.0 without any side effects, The VEX firmware 3.0 will work well also with older NerdSEQ versions)!
Please follow this update order (important for the VEX!!!):
1. Copy the NerdSEQ V3.0 firmware (unpacked, 'nerdseq.hex') into the firmware folder of the NerdSEQ SD Card.
2. (optional) Copy the video expander V3.0 firmware (unpacked, 'vex_3_0.vex') into the firmware folder of the NerdSEQ SD Card.
3. (optional) Unpack the 'shaders.zip' file onto the NerdSEQ SD Card root (Unpacking will create a folder on the NerdSEQ root called 'shaders'.) The shaders in that folder are a collection of fragment shaders taken from different (open) sources. Most of the shaders run as they are (all files that start with SHxx) but are not enhanced yet to be used with all the NerdSEQ modulations. All shaders that got proper names (eg PLASMA.FRAG) are optimized and extended with NerdSEQ modulations.
4. Update the NerdSEQ firmware.
5. (optional) With the new NerdSEQ firmware V3.0 running, update the Video Expander firmware. There is no need to disconnect any other expander. Go to Setup->Expander FW Update. Choose the firmware file: VEX_3_0.VEX and press OK. Choose Update Now and it will start the update. Once finished it will show the detected new video expander firmware.
The Video Expander must be enabled (in clone mode) and fully working already to be able to do the update. That means also that both cables, the 12 pin (midi) and the 14 pin (NSA) ribbon cables must be connected with the NerdSEQ (and be sure you don't break the SD Card if the 12 pin cable has not been installed yet. The usual hotplug rules apply)!
6. Enjoy!
Here is the changelog:
Dualchord
- added dualchord presets (page 88)
- added dualchord preset import/export (page 88)
- added notes to dualchord CV/MOD FX and patch (page 84+)
- fixed dualchord Note FX which was half a note wrong, added note off
- added missing dualchord LFO FX (page 84+)
- added dualchord FX command to set note mode and change presets (page 84+)
- fixed dualchord random FX functions
- fixed dualchord kill FX function
- fixed FX execution for dualchord patch
- added set dualchord preset command in mappings (page 206)
- added Part Mode to dualchord setting FX (page 84+)
- fixed dualchord knob selection for velocity
- reduced amount of patches and increased amount of patch rows (fixes dualchord patch bug)
Video Expander / Video Synthesis
- added video synthesizer functionality with the use of glsl shaders (page 106)
- added new video expander firmware update which uses the .VEX extension (page 228)
- added Video destinations to mappings (page 206)
- added shortcut to enter video project screen (PROJECT button twice) only if the VEX got Firmware 3.0 (page 107)
- added HDMI Mode and Group to the settings so all video modes can now be used (page 119)
- added current value screen for video
- added automator destinations for video (page 137)
- added patch and tables for video (from FX)
- added multiple modulation possibilities as well as dedicated envelopes and LFOs for the video synthesis (page 111)
- updated video patterns/tracktype for a complete integration in the sequence (page 113)
General
- fixed knob input from Multi-IO in first MODE A
- fixed patch execution for Patch notes and other functions
- added tables for all tracktypes (page 126)
- added 6 possible executable columns for tables (page 130)
- added table -> no note/retrigger 'transpose command' '***' (page 127)
- added velocity overrule FX to midi which can be used to have in/decreasing volumes combined with tables (midi delay) (page 61)
- added clock in auto-start on demand (page 149)
- fixed clock settings from track setup menu
- Shift+F9 on keyboard switches to video project screen
- fixed set CV16 note from mapping
- updated ART commands to send CC, Portamento, Pitchbend etc, fixed transpose issue with ART notes (page 101)
- fixed copy/paste between Modular FX
- added copy/paste between Trigger16 and I2C drummatrix
- added live globaltranspose update
- fixed record to audio track 8 from Midi
- fixed mapping overflow of automator values with an offset
- added scale direction setting in mappings (page 202)
- fixed wrong text for midi mapping source commands (eg program change)
- fixed Midi hanging notes if used with output offset
- fixed CV16 note output on NSA 2 with mappings
- added return to sequencer screen from Launchpad Modular pattern again
- added velocity with midi note off
- added new Midi note destinations for the mappings which is a combined source for gate and note (page 203)
- Fixed midi note preview and note input with note offset and scales
And as usual many little fixes...
Here you can find the latest manual for V3.0:
https://forum.xor.eu/showthread.php?tid=1998
The updates and the manual are also always available to download on the regular website:
https://xor-electronics.com/nerdseq/
Please spread the word so I can continue working on this!
nerdseq.hex (Size: 5,44 MB / Downloads: 178)
nerdseq.zip (Size: 1,71 MB / Downloads: 72)
vex_3_0.vex (Size: 1,33 MB / Downloads: 41)
vex_3_0.zip (Size: 449,36 KB / Downloads: 23)
shaders.zip (Size: 299,59 KB / Downloads: 51)
Welcome V3.0!
As usual loads of new features, fixes and if you got a Video Expander then you get also a Video Synthesizer for free! If you don't then now is the time to get your hands on a VEX ;-)
Important information before you update!!!
- make a backup of your SD Card and especially of your projects (can't stop repeating that!!)
- Firmware update FAQ for some infos. https://forum.xor.eu/showthread.php?tid=4
- No worries, in case of any issues you can always go back to your earlier version (but can't load projects that have been saved with V3.0 without any side effects, The VEX firmware 3.0 will work well also with older NerdSEQ versions)!
Please follow this update order (important for the VEX!!!):
1. Copy the NerdSEQ V3.0 firmware (unpacked, 'nerdseq.hex') into the firmware folder of the NerdSEQ SD Card.
2. (optional) Copy the video expander V3.0 firmware (unpacked, 'vex_3_0.vex') into the firmware folder of the NerdSEQ SD Card.
3. (optional) Unpack the 'shaders.zip' file onto the NerdSEQ SD Card root (Unpacking will create a folder on the NerdSEQ root called 'shaders'.) The shaders in that folder are a collection of fragment shaders taken from different (open) sources. Most of the shaders run as they are (all files that start with SHxx) but are not enhanced yet to be used with all the NerdSEQ modulations. All shaders that got proper names (eg PLASMA.FRAG) are optimized and extended with NerdSEQ modulations.
4. Update the NerdSEQ firmware.
5. (optional) With the new NerdSEQ firmware V3.0 running, update the Video Expander firmware. There is no need to disconnect any other expander. Go to Setup->Expander FW Update. Choose the firmware file: VEX_3_0.VEX and press OK. Choose Update Now and it will start the update. Once finished it will show the detected new video expander firmware.
The Video Expander must be enabled (in clone mode) and fully working already to be able to do the update. That means also that both cables, the 12 pin (midi) and the 14 pin (NSA) ribbon cables must be connected with the NerdSEQ (and be sure you don't break the SD Card if the 12 pin cable has not been installed yet. The usual hotplug rules apply)!
6. Enjoy!
Here is the changelog:
Dualchord
- added dualchord presets (page 88)
- added dualchord preset import/export (page 88)
- added notes to dualchord CV/MOD FX and patch (page 84+)
- fixed dualchord Note FX which was half a note wrong, added note off
- added missing dualchord LFO FX (page 84+)
- added dualchord FX command to set note mode and change presets (page 84+)
- fixed dualchord random FX functions
- fixed dualchord kill FX function
- fixed FX execution for dualchord patch
- added set dualchord preset command in mappings (page 206)
- added Part Mode to dualchord setting FX (page 84+)
- fixed dualchord knob selection for velocity
- reduced amount of patches and increased amount of patch rows (fixes dualchord patch bug)
Video Expander / Video Synthesis
- added video synthesizer functionality with the use of glsl shaders (page 106)
- added new video expander firmware update which uses the .VEX extension (page 228)
- added Video destinations to mappings (page 206)
- added shortcut to enter video project screen (PROJECT button twice) only if the VEX got Firmware 3.0 (page 107)
- added HDMI Mode and Group to the settings so all video modes can now be used (page 119)
- added current value screen for video
- added automator destinations for video (page 137)
- added patch and tables for video (from FX)
- added multiple modulation possibilities as well as dedicated envelopes and LFOs for the video synthesis (page 111)
- updated video patterns/tracktype for a complete integration in the sequence (page 113)
General
- fixed knob input from Multi-IO in first MODE A
- fixed patch execution for Patch notes and other functions
- added tables for all tracktypes (page 126)
- added 6 possible executable columns for tables (page 130)
- added table -> no note/retrigger 'transpose command' '***' (page 127)
- added velocity overrule FX to midi which can be used to have in/decreasing volumes combined with tables (midi delay) (page 61)
- added clock in auto-start on demand (page 149)
- fixed clock settings from track setup menu
- Shift+F9 on keyboard switches to video project screen
- fixed set CV16 note from mapping
- updated ART commands to send CC, Portamento, Pitchbend etc, fixed transpose issue with ART notes (page 101)
- fixed copy/paste between Modular FX
- added copy/paste between Trigger16 and I2C drummatrix
- added live globaltranspose update
- fixed record to audio track 8 from Midi
- fixed mapping overflow of automator values with an offset
- added scale direction setting in mappings (page 202)
- fixed wrong text for midi mapping source commands (eg program change)
- fixed Midi hanging notes if used with output offset
- fixed CV16 note output on NSA 2 with mappings
- added return to sequencer screen from Launchpad Modular pattern again
- added velocity with midi note off
- added new Midi note destinations for the mappings which is a combined source for gate and note (page 203)
- Fixed midi note preview and note input with note offset and scales
And as usual many little fixes...
Here you can find the latest manual for V3.0:
https://forum.xor.eu/showthread.php?tid=1998
The updates and the manual are also always available to download on the regular website:
https://xor-electronics.com/nerdseq/
Please spread the word so I can continue working on this!
nerdseq.hex (Size: 5,44 MB / Downloads: 178)
nerdseq.zip (Size: 1,71 MB / Downloads: 72)
vex_3_0.vex (Size: 1,33 MB / Downloads: 41)
vex_3_0.zip (Size: 449,36 KB / Downloads: 23)
shaders.zip (Size: 299,59 KB / Downloads: 51)
PLEASE use the search function if something have been asked or discussed before.
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!
Every (unnessesary) forum support means less time to develop! But of course, i am here to help!
