Continuing my suggestions -

MODIFY MARKED VALUES [SHIFT CURSOR UP/DOWN/LEFT/RIGHT]

I have suggested this before, and others have as well. I think it fits perfectly in line with how it currently works, it just extends functionality. It's even so intuitive I thought this was how it worked before I tried it, and when I looked at the M8 functionality just before writing this post it actually is laid out exactly like this.

It could look like this:
   

Here we see a marked block, and then we do a small shift using SHIFT+RIGHT, then a larger shift using SHIFT+UP.
Every cell acts simply as if we had used SHIFT+CURSOR on it - it is up to the user to not mark something they don't want to change.
Empty cells do not get incremented/decremented.

I suggest that the current mark from left/right currently taking up SHIFT+CURSOR when marking be replaced with OK+CURSOR - it makes perfect sense to always change values in the same way.



DRAG Functionality [SHIFT + UP/DOWN]

I suggest that we allow a drag functionality, both inside and outside of marking.

When we have marked values it could look like this:

   

As we drag it downwards it displaces the other cells, moving past them. *Last image jumped two rows

Without marking, we can drag single cells:

   

SHIFT/ROTATE Shortcut [SHIFT+OK+UP/DOWN]

I suggest the shift functionality that is in the NERD menu be put on this shortcut. This way all the manipulation is easy to see while you're doing it, a huge issue imo while using shift/rotate.
I don't have pictures of this, but just like it works right now except it's on a shortcut.

Heya, coming at you with a couple of ideas I've thought about for a long time. Splitting into parts for readability and forum restrictions on attachments.

MARK Shortcut - [SEQ]
I suggest a shortcut for marking where we press the SEQUENCER button (*same as MARK button) to mark the entire ROW, COLUMN or the entire viewable PATTERN.
When we press a 4th time we return to our original MARK, unless we changed the marking in any way (it is then like starting over, marking that entire ROW, COL, PATTERN, etc).

Here are some images to illustrate it (please excuse the sometimes blurry image):

   

This shows us marking from just one cell. Again, pressing SEQ once more would return to the original cell unless the marking was changed. Any change resets this functionality.

   

This shows marking from a bigger block. Pressing once extends to the ROWS, again extends the COLUMNS, again marks the entire viewable screen, and once more would return to original mark.

   

Once again, showing what it'd look like on a different column. Extending ROW, then COLUMN, then viewable pattern screen, and then back.
If we were to alter the selection after extending to, for example, the column, we would then once again be extending to the ROW if we pressed again.



Justification:
It'd be a great way of marking - the only downside is you won't go to the sequencer screen, but already pressing PATCH or TABLE doesn't move you anywhere when you're marking.
I think it makes sense in a button combo way, as you press SHIFT + SEQ(MARK) then press again without the shift to alter the marking.

Is it possible to apply tempo change +/- using CV input?

I cut down some acrylic today and fit perfectly into the screen. I swear it brightens things up, just a bit.
If anyone wants to do the same 2mm acrylic will do the trick. Get a close measurement, score some lines and break the plastic into shape. I then sanded edges lightly, test fit, sand again and so on until a perfect fit.

   

hello, I plan to do the cv calibration, I don't know much about electronics, would you have any advice and material to advise me to do the best calibration (without spending a fortune) thank you

setup->user interface setup->RESET COLOURS->OK

The reset to default colours is next to SAVE. 
Press OK on the reset and your user interface edits are gone.

A verify prompt, or simpler, restore the default colours in the picker screen, 
but only a SAVE makes them permanent.

--

I just got one for the box, and I seems a bit of a tricky module to get any information on.

Getting there.    

Send two tracks to one pair of CV outputs like a Precision Adder, I know the Table functions offers this kind of thing but might offer more with 2 separate tracks

Rotate Notes in a Pattern by Tick Amount so to be able send one pattern out of phase with another , a bit like the phase piano trick but being able to specify and hold on any sweet spots in phasing