.... successfully mount the 'more video' expander inside their case?

I have a SIX_90 case from blackhole cases, and am exactly 6 hp short of having room for a filter module I have, and I only use the vid module for its keyboard control which can be connected via bluetooth.    While im here, has anyone managed to bluetooth connect the video display?

Similar to how the fill-CV works on Grids, I'd like to be able to send a high CV signal to the nerdseq and that would create a fill on kick or snare on my Trigger 16 tracks.

I was trying to see how I can do this but could only figure out switching to new patterns through the CV inputs. Can anyone guide me to the right direction here? Can I use the automator in some way together with probability?

Thanks in advance!

   
   


Nerdseq is the best eurorack sequencer, obviously. I could write a book about how much I love it.

In this case Nerdseq is fully controlling eight voices and some effects, as well as all the CV generator modules.
I`m using two CV Tracks per CV Expander and I enjoy programming every aspects of a sounds step by step.
Patches, precise probability programming and all the Envs/LFOs are extremely useful for me.

Millions of thanks, Thomas Margolf, and huge respect!

Cheers
Adam

1) press PROJECT
2) use CURSOR DOWN to select Load Sample
3) press OK
4) press CURSOR DOWN to SAMPLE SLOT 00
5) press OK to open sample selection screen (shows all samples on SD card)
6) select 626 CHH.RAW
7) press SHIFT+RIGHT CURSOR to pre-listen sample on hardware output SAMPLE8

Bug: no sound is heard on output SAMPLE8

The output on SAMPLE8 is also not working with these samples:
SA-10 SNARE2
TR808 CLAP
RAVE CLASSIC2
AFD HIT038
ICREVPNO

Pre-listening on output SAMPLE7 by pressing SHIFT+LEFT CURSOR is working fine with all samples.

1) press PROJECT
2) use CURSOR DOWN to select Load Sample
3) press OK
4) press CURSOR DOWN to SAMPLE SLOT 00
5) press OK to open sample selection screen
6) do nothing, just wait until SCREEN SAVER activates

Bug: System freezes - no way to exit the SCREEN SAVER

(SCREEN SAVER activation time set to 1 min)

1) go to AUTOMATOR SCREEN
2) set any AUTOMATOR (it really doesn't matter which, e.g. LFO)
3) press DOWN to go on lower half of screen
4) press SHIFT+DELETE

Glitch: No cursor navigation in lower screen is not possible anymore, but you can still press UP to go to upper half of the screen. Then, the AUTOMATOR is finally deleted.

It seems SHIFT+DELETE is acting globally on the AUTOMATOR SCREEN.

I came across this, when trying whether the LFO-OFFSET could be put back into neutral position by pressing SHIFT+DELETE.

Proposal: SHIFT+DELETE has no function in lower part of screen.

Alternative proposal: SHIFT+DELETE has only field specific functionality when in lower half of the screen, e.g. setting LFO-OFFSET to center position when the cursor is placed on the LFO-OFFSET field.

(On 1.26 RC6, the system completely crashed when pressing SHIFT+DELETE in the lower AUTOMATOR SCREEN)

Hi folks. Does anybody kno if it’s possible to connect the pins on the midi port on back of the nerd directly to the midi port on the intellijel case? And which pins are for what?

I did not find anything in the manual, so my question is the following:


Does the More Video IO expander expect an American English keyboard or is there some option to choose a layout?

I assume I just have to ignore the labeling on the keys and everything will work....

Is it possible to trigger the trigger 16 via midi input?

I have a load of drum patterns on my Digitakt, and now that it has song mode it’s very handy!

Hi, 

I'm not sure if this has been covered before, so I write in the feature request forum.
Is there a way to copy notes information from a midi (or CV16) pattern to a modular pattern and vice versa? I've tried (with mark and copy) and as for now it doesn't seem to be possible. 
It could avoid re-entering all notes when transforming a midi pattern to modular or the opposite.